dhh_1981 发表于 2007-12-4 14:03:34

一个关于冲压成形的例子发给大家

大家练习练习把。做好拉要把结果贴上拉阿

dhh_1981 发表于 2007-12-7 14:00:46

this is my first time to give some information,
it is a good example of stamping, including forming, springback,anneal.
althougn it was done by ABAQUS in the paper,the method is good for all of us.

zhufeiyu830 发表于 2007-12-8 16:16:39

我顶．．谢谢

dhh_1981 发表于 2007-12-11 10:04:03

谢谢大家！

我把自己做的结果贴上来啦。

遗憾的是在ANNEAL以及第二步冲压过程中凹模阻尼器没有弄成功！

dhh_1981 发表于 2007-12-11 10:04:37

请大虾帮忙给点建议！尤其是阻尼器的问题

simulationstar 发表于 2007-12-11 14:39:54

看看！

mstgracie 发表于 2007-12-12 10:36:23

好，多谢楼主

好，多谢楼主
好，多谢楼主

CCFF 发表于 2007-12-15 14:27:19

先下来看看:)

spydz 发表于 2007-12-28 17:24:42

:) 谢谢楼主

ssunggang 发表于 2008-1-15 15:57:48

用什么软件做的啊！介绍一下

dhh_1981 发表于 2008-1-17 16:21:27

abaqus
先采用显式分析做成形，然后采用隐式分析作回弹。
通过IMPORT 将成形模型导入隐式分析中。

lsw00000901 发表于 2008-2-17 12:38:41

thanks

fortunately 发表于 2008-4-14 12:53:07

谢谢 热心人

yandejun 发表于 2008-4-18 18:49:51

回复 1# 的帖子

好啊，感谢了啊。;P ;P

haustber 发表于 2008-5-19 23:54:52

多谢楼主！！！

蓝魂归来 发表于 2008-6-1 13:33:10

能不能用DEFORM做？

有没有DEFORM做的冲压方面的例子 谢谢分享啊
我的邮箱xiaoxiaoquan00@126.com

蓝魂归来 发表于 2008-6-1 13:40:20

为什么下不了啊

下到90%左右就下不了了！
能发我邮箱里吗 谢谢
xiaoxiaoquan00@126.com

xinyi826 发表于 2008-8-6 09:42:15

谢谢楼主啊

shenshijun1983 发表于 2008-8-7 23:23:05

比较全面的冲压例子

dhh_1981 发表于 2008-8-21 19:40:23

i am so glad that so many people take part in stamping simulation.

As i know, most of stamping simulation is done by DYNAFORM and AUTOFORM. These software are professional, are also effective. But the key is about a lot of parameters of simulation, which depend on work accumulation.

Good Luck for all of stamping simulation friends.
页: [1] 2 3
查看完整版本: 一个关于冲压成形的例子发给大家