找回密码
 注册
Simdroid-非首页
查看: 98|回复: 2

输电塔线建模问题

[复制链接]
发表于 2018-3-27 10:06:48 | 显示全部楼层 |阅读模式 来自 江苏徐州
悬赏1仿真币已解决
我在建模过程中,使用beam188单元建立铁塔,mpc184单元建立绝缘子,link10单元建立导线,三者连接处都有共用节点,边界条件都设置了,但在施加重力加速度计算时一直算不了,请问连接处需要特殊处理吗?                                以下的节点都是导线上的节点,求大神指点! *** WARNING ***   SUPPRESSED MESSAGE    CP =    1039.656   TIME= 09:34:51
There is at least 1 small equation solver pivot term (e.g., at the UX   
degree of freedom of node 1) which may indicate a numerically unstable  
model.  Please check your results carefully.                           

*** ERROR ***     SUPPRESSED MESSAGE    CP =    1039.719   TIME= 09:34:51
The value of UX at node 44124 is 9.259705723E+10.  It is greater than   
the current limit of 1000000 (which can be reset on the NCNV command).  
  This generally indicates rigid body motion as a result of an           
unconstrained model.  Verify that your model is properly constrained.   

*** ERROR ***     SUPPRESSED MESSAGE    CP =    1039.719   TIME= 09:34:51
*** MESSAGE CONTINUATION ---- DIAGNOSTIC INFORMATION ***               
Rigid body motion can also occur when net section yielding has         
occurred resulting in large displacements for small increments of load  
or when buckling has occurred.  You can plot the time history curve     
for node 44124 in the UX direction to check for stiffness (slope of     
the curve) approaching zero.                                            

*** WARNING ***   SUPPRESSED MESSAGE    CP =    1057.062   TIME= 09:35:00
There is at least 1 small equation solver pivot term (e.g., at the UX   
degree of freedom of node 1) which may indicate a numerically unstable  
model.  Please check your results carefully.                           

*** ERROR ***     SUPPRESSED MESSAGE    CP =    1057.094   TIME= 09:35:00
The value of UX at node 43480 is 3.374903337E+21.  It is greater than   
the current limit of 1000000 (which can be reset on the NCNV command).  
  This generally indicates rigid body motion as a result of an           
unconstrained model.  Verify that your model is properly constrained.   

*** ERROR ***     SUPPRESSED MESSAGE    CP =    1057.094   TIME= 09:35:00
*** MESSAGE CONTINUATION ---- DIAGNOSTIC INFORMATION ***               


*** WARNING ***   SUPPRESSED MESSAGE    CP =    1057.094   TIME= 09:35:00
The unconverged solution (identified as time 1 substep 999999) is      
output for analysis debug purposes.  Results should not be used for     
any other purpose.   

最佳答案

查看完整内容

问题应该出在 link10 单元,因为 link10 单元不能抗弯,其节点只有平移自由度,在横向载荷作用下,会产生刚体运动。 因此,在做输电塔线为题时,对 link10 单元必须设置为只拉,且必须设置初始应变,然后进行预应力分析。 给你一些资料作为参考吧:
发表于 2018-3-27 10:06:49 | 显示全部楼层 来自 上海
Simdroid开发平台
  问题应该出在 link10 单元,因为 link10 单元不能抗弯,其节点只有平移自由度,在横向载荷作用下,会产生刚体运动。
  因此,在做输电塔线为题时,对 link10 单元必须设置为只拉,且必须设置初始应变,然后进行预应力分析。
  给你一些资料作为参考吧:


























本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?注册

×
回复

使用道具 举报

 楼主| 发表于 2018-4-1 13:56:31 | 显示全部楼层 来自 江苏徐州
感谢大佬的指点与资料,感谢感谢
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|小黑屋|联系我们|仿真互动网 ( 京ICP备15048925号-7 )

GMT+8, 2024-3-29 15:52 , Processed in 0.028476 second(s), 10 queries , Gzip On, MemCache On.

Powered by Discuz! X3.5 Licensed

© 2001-2024 Discuz! Team.

快速回复 返回顶部 返回列表