感应加热出现无.rst文件可用的问题
我作的是电磁感应加热，可是在计算时出现了这样的error.No results file ( xx.rst ) available. The LDREAD command is ignored.
这是为什么，请大侠帮忙解决一下。
/BATCH
/CPLANE,1
/CLEAR,NOSTART
/VIEW,1,1,1,1
WPSTYLE,,,,,,,,0
/config,nres,3000000
/Nerr,1,1500000
/filenam,induction1
/prep7
/title,Induction Heating
et,1,117 !non-steel region
et,2,117,1 !steel region
et,3,117,1 !coil
*SET,freq,40000 ! frequency (Hz.)
*SET,pi,4*atan(1) ! pi
*SET,cond,.392e7 ! maximum conductivity
*SET,muzero,4e-7*pi ! free-space permeability
*SET,mur,200 ! maximum relative permeability
*SET,skind,sqrt(1/(pi*freq*cond*muzero*mur)) ! skin depth
*SET,ftime,20 ! final time
*SET,tinc,1 ! time increment for harmonic analysis
*SET,time,0 ! initialize time
*SET,delt,1 ! maximum delta time step
emunit,mks ! set magnetic units
mp,murx,1,1 ! air relative permeability
mptemp
mptemp,1,25.5,160,291.5,477.6,635,698 ! temps for relative permeability
mptemp,7,709,720.3,742,761,1000
mpdata,murx,2,1,200,190,182,161,135,104 ! steel relative permeability
mpdata,murx,2,7,84,35,17,1,1
mptemp
mptemp,1,20,100,200,400,600 ! temps for resistivity
mpdata,rsvx,2,1,2.23e-7,2.71e-7,3.42e-7,5.29e-7,7.85e-7
mptemp
mptemp,1,0,100,300,500,1200 ! temps for conductivity
mpdata,kxx,2,1,42.7,42.7,40.6,37.3,30.1
mp,dens,2,7850
mp,c,2,465
mp,dens,3, 8960
mp,RSVX,3,1.7e-8
mp,murx,3,1
BLOCK,-10.5/1000,-0.5/1000,-35/1000,35/1000,0/1000,80/1000
BLOCK,0.5/1000,10.5/1000,-35/1000,35/1000,0/1000,80/1000
WPAVE,10.5/1000,50/1000,7.5/1000
wpro,,,90
CYL4, , ,4/1000
CYL4, , ,3/1000
ASBA, 13, 14
wpro,,,-90
K,38,25/1000,50/1000,7.5/1000
K,39,25/1000,-50/1000,7.5/1000
K,40,-25/1000,-50/1000,7.5/1000
K,41,-25/1000,50/1000,7.5/1000
L,38,39
L,39,40
L,40,41
L,41,38
LFILLT,36,33,15/1000,
LFILLT,33,34,15/1000,
LFILLT,34,35,15/1000,
LFILLT,35,36,15/1000,
FLST,8,8,4
FITEM,8,37
FITEM,8,33
FITEM,8,38
FITEM,8,34
FITEM,8,39
FITEM,8,35
FITEM,8,40
FITEM,8,36
VDRAG, 15, , , , , ,P51X
alls
WPAVE,0,0,0
WPSTYLE,,,,,,,,0
FLST,3,8,6,ORDE,2
FITEM,3,3
FITEM,3,-10
VGEN,5,P51X, , , , ,16/1000, ,0
BLOCK,0.2,-0.2,0.16,-0.16,0.18,-0.1
alls
VOVLAP,ALL
VGLUE,ALL
NUMCMP,AREA
NUMCMP,VOLUME
FLST,5,40,6,ORDE,2
FITEM,5,3
FITEM,5,-42
VSEL,S, , ,P51X
VATT,3,1,3
FLST,5,2,6,ORDE,2
FITEM,5,1
FITEM,5,-2
VSEL,S, , ,P51X
VATT,2,1,2
FLST,5,6,6,ORDE,2
FITEM,5,43
FITEM,5,-48
VSEL,S, , ,P51X
VATT,1,1,1
alls
FLST,5,2,6,ORDE,2
FITEM,5,1
FITEM,5,-2
VSEL,S, , ,P51X
FLST,5,4,4,ORDE,4
FITEM,5,2
FITEM,5,7
FITEM,5,16
FITEM,5,-17
CM,_Y,LINE
LSEL, , , ,P51X
CM,_Y1,LINE
CMSEL,,_Y
LESIZE,_Y1, , ,20,10, , , ,1
FLST,5,4,4,ORDE,4
FITEM,5,4
FITEM,5,-5
FITEM,5,14
FITEM,5,19
CM,_Y,LINE
LSEL, , , ,P51X
CM,_Y1,LINE
CMSEL,,_Y
LESIZE,_Y1, , ,20,0.1, , , ,1
FLST,5,16,4,ORDE,9
FITEM,5,1
FITEM,5,3
FITEM,5,6
FITEM,5,8
FITEM,5,-13
FITEM,5,15
FITEM,5,18
FITEM,5,20
FITEM,5,-24
CM,_Y,LINE
LSEL, , , ,P51X
CM,_Y1,LINE
CMSEL,,_Y
LESIZE,_Y1, , ,30, , , , ,1
FLST,5,2,6,ORDE,2
FITEM,5,1
FITEM,5,-2
CM,_Y,VOLU
VSEL, , , ,P51X
CM,_Y1,VOLU
CHKMSH,'VOLU'
CMSEL,S,_Y
VSWEEP,_Y1
CMDELE,_Y
CMDELE,_Y1
CMDELE,_Y2
FLST,5,40,6,ORDE,2
FITEM,5,3
FITEM,5,-42
VSEL,S, , ,P51X
vsweep,all
alls
FLST,5,5,6,ORDE,2
FITEM,5,43
FITEM,5,-47
VSEL,S, , ,P51X
SMRT,6
MSHAPE,1,3D
MSHKEY,0
VMESH,all
alls
CM,_Y,VOLU
VSEL, , , , 48
CM,_Y1,VOLU
CHKMSH,'VOLU'
CMSEL,S,_Y
!*
VMESH,_Y1
!*
CMDELE,_Y
CMDELE,_Y1
CMDELE,_Y2
alls
VPLOT
SAVE
FINISH
/SOLU
ASEL,S, EXT
DA,ALL,AZ,0
ASEL,ALL
FLST,5,5,6,ORDE,2
FITEM,5,38
FITEM,5,-42
VSEL,S, , ,P51X
eslv
esln,r,1
bfe,all,js,1,4.55e6,,
FLST,5,5,6,ORDE,5
FITEM,5,6
FITEM,5,13
FITEM,5,20
FITEM,5,27
FITEM,5,34
VSEL,S, , ,P51X
eslv
esln,r,1
bfe,all,js,1,-4.55e6,,
FLST,5,15,6,ORDE,10
FITEM,5,3
FITEM,5,-5
FITEM,5,10
FITEM,5,-12
FITEM,5,17
FITEM,5,-19
FITEM,5,24
FITEM,5,-26
FITEM,5,31
FITEM,5,-33
VSEL,S, , ,P51X
eslv
esln,r,1
BFE,ALL,JS, 1, ,-4.55e6,
FLST,5,15,6,ORDE,10
FITEM,5,7
FITEM,5,-9
FITEM,5,14
FITEM,5,-16
FITEM,5,21
FITEM,5,-23
FITEM,5,28
FITEM,5,-30
FITEM,5,35
FITEM,5,-37
VSEL,S, , ,P51X
eslv
esln,r,1
BFE,ALL,JS, 1, ,4.55e6,
ALLS
/solu
antyp,harm
harfrq,40000
HROPT,FULL
HROUT,ON
EQSLV, ,1e-008,
physics,write,emag ! write emag physics file
solve
SAVE
finish
/prep7
lsclear,all ! clear all b.c.'s and options
et,1,0 ! non-steel
et,2,SOLID90 ! steel
et,3,0
finish
/solu
antype,trans
toffst,273
tunif,50 ! initial uniform temperature
cnvtol,heat,1 ! convergence tolerance
kbc,1 ! step loads
trnopt,full
autos,on ! auto time-stepping
deltim,1e-1,1e-2,delt,on ! time step control
outres,basic,all ! save all load step information
physics,write,thermal ! write thermal physics file
finish
*do,i,1,ftime/tinc ! solution *do loop
*SET,time,time+tinc ! increment time
physics,read,emag ! read emag physics file
/solu
*if,i,eq,1,then
tunif,50 ! initial temperature
*else
ldread,temp,last,,,,,rth ! read thermal analysis temperatures
*endif
solve ! solve harmonic analysis
finish
physics,read,thermal ! read thermal physics file
/assign,esav,therm,esav ! redirect files for use in thermal restart
/assign,emat,therm,emat
/solu
*if,i,gt,1,then
antype,trans,rest ! thermal restart
*endif
time,time ! time at end of thermal run
esel,s,mat,,2 ! select billet region
ldread,hgen,,,,2,,rst ! apply coupled joule heating load from emag
esel,all
solve
finish
/assign,esav ! reassign files to default
/assign,emat
*enddo ! end of solution looping
save
finish 做磁热耦合分析的都没有遇过这个错误吗?
该如何解决，请大家帮忙解救
谢谢 写成rth，试试
以前好像有人问过，直接用rth 磁分析结果为rst,再把此结果带入分析热,副档名为rth,您的意思是磁分析直接写成rth,那我热分析不就要写成rst,印象中记得不同的副档名有限定储存分析的领域范围,热分析就要写成rth,这样好像就会与您提出的想法出现冲突,或是我误会您的意思
我有找寻之前相同问题发问的文章,有人说是单元体的问题,但我用相同的单元体在别的case上是可以分析,偏偏在我这case是不行,因为那篇是前年的问题,想问问板上大侠,此问题有新的解决发法或是有新的见解,能提供给我参考,谢谢 哦，看错了，后一个磁场的结果应该是rmg文件吧，你看你的盘里应该有rmg。
ansys理论上，磁场分析的结果是rmg，热场是rth文件。
以前有人问过没有rmg文件，在论坛上讨论，后来也没有准确的解释。没有rmg就用rst了。 我只有rst,但是它档案为0MB,这个错误要怎解决阿
很奇妙的错误,有时候可以但改变模型就会有这问题 我觉得你还是重新建模吧，换一种建模方法，仔细检查各项参数，大体的磁热耦合过程就是这样的。有限元分析急不得。
你的命令流好多都是交互的，需要正规的命令流。 楼主
你的问题解决了吗？
如果解决了的话
能把你的命令流发到我邮箱里吗》
qu717@163.com
页:
[1]