surface-based cohesive模拟加筋板脱层失效
我现在在用surface-based cohesive 模拟加筋板脱层失效,在interaction 中surface to surface contact中,不知道应该怎么设置interaction property,请问有没有高手知道,界面元的性质怎么在interaction property中赋予。 其实是很简单的。首先进入interaction模块,建立一个接触属性,mechanical属性里选择cohesive behavior
里面可以制定三条拉伸分离曲线的斜率KnnKttKss 也就是三个刚度值
然后在mechanical中选择damage,里面可以指定损伤初始值和损伤演化值、粘性系数。
祝你好运。 自己顶一下,各位高手看一下啊
我在壁板和蒙皮之间加的surface to surface contact模拟脱层失效 waiting for so many days,but no answer. You have to give below commands (includig relative parameters) in your inp file.
*surface interaction
*cohesive behavior
*damage initiation
*damage evolution 怎么没有人支持呀 好像6.81没有
没用过 8# seawideyp
“6.81没有”? To #8
It is one of the new functions in 6.8. 本帖最后由 c00 于 2009-12-24 15:39 编辑
10# abelyang
可不可以多说一点呢 You can try first
*cohesive behavior
instead of *cohesive behavior,eligibility=specified contacts
Beacuse I can not see you set *INITIAL CONDITIONS in your inp to specify special slave & master surface. 本帖最后由 c00 于 2009-12-24 15:29 编辑
12# abelyang
刚刚试了你说的方法改了一下,还是不行,我再找找问题所在,有问题再问你 12# abelyang
你说的“INITIAL CONDITIONS ”应该是指有裂纹用的吧?我想模拟的没有初始裂纹,请问可不可以用surface-based cohesive 来模拟脱粘? Set ELIGIBILITY=SPECIFIED CONTACTS to restrict cohesive behavior to a subset of slave nodes defined using *INITIAL CONDITIONS, TYPE=CONTACT. This parameter value is available only for Abaqus/Standard analyses. ( from Abaqus Keywords Reference Manual )
And 可以用surface-based cohesive 来模拟脱粘. I had exeperiences in Abaqus/explicit. 15# abelyang
请问,我模拟无裂纹的加筋板脱粘,我建了两个part,part1是帽型加筋条,part2是蒙皮,中间用surface-based cohesive连接,这样对不对?还是应该建立一个part?
能不能说一下在abaqus/explicit中模拟的方法?谢谢:handshake 好像不好可以在explicit中用surface-to-surface来定义cohesive吧 13# abelyang 15# hopeflydream
http://forum.simwe.com/viewthread.php?tid=918863&highlight=cohesive taishanbuzuo 发表于 2010-5-16 18:44 static/image/common/back.gif
其实是很简单的。
首先进入interaction模块,建立一个接触属性,mechanical属性里选择cohesive behavior
里 ...
谢谢,又学到一招。 直接用COHESIVE的UEL或者UMAT程序好了。我现在做内聚力的二次开发,光点点软件一点意思没有 你好,可以交流下吗?我的QQ:598124303,马东华 也是做cohesive
页:
[1]
2