缩减连杆曲轴模板时 遇到的问题

chenminghuafz

蓝博士你好：
我用nastran2005r2缩减你给出的2005模板，在缩减连杆和曲轴的时候都可以产生所需要的out2等文件，但f06文件有警告错误，我把f06警告的地方贴出来，蓝博士帮看一下，是可以这样，还是有错误？我不知道什么怎么回事？忘解答，困惑中~！

chenminghuafz

** USER WARNING MESSAGE 6450 (OUTPT4)
     THE SELECTION OF THE  ASCII FORMAT OPTION IN THE OUTPUT4 MODULE FOR DATABLOCK KSAA     MAY RESULT IN NUMERIC TRUNCATION.
     USER INFORMATION:
      1. THE FORTRAN FORMAT BEING USED IS (1P,5E16.9)
      2. THE DEFAULT FORTRAN FORMAT IS (1P,5E16.9)
      3. THE FIFTH PARAMETER OF THE OUTPUT4 MODULE CAN BE USED TO INCREASE THE NUMBER OF SIGNIFICANT DIGITS.
     USER ACTION:
      1. IF THE NUMBER OF SIGNIFICANT DIGITS IS ACCEPTABLE, THEN NO ACTION IS REQUIRED.
      2. IF ADDITIONAL SIGNIFICANT DIGITS ARE REQUIRED, THEN INCREASE THE VALUE OF THE FIFTH PARAMETER, AND
         RERUN THE JOB.
DATA BLOCK KSAA    WRITTEN ON FORTRAN UNIT   33 FROM DMAP MODULE OUTPUT4 IN ASCII FORMAT (1P,5E16.9)         
TRAILER =     101     750     750       6       2    1320    7746
** USER WARNING MESSAGE 6450 (OUTPT4)
     THE SELECTION OF THE  ASCII FORMAT OPTION IN THE OUTPUT4 MODULE FOR DATABLOCK MSAA     MAY RESULT IN NUMERIC TRUNCATION.
     USER INFORMATION:
      1. THE FORTRAN FORMAT BEING USED IS (1P,5E16.9)
      2. THE DEFAULT FORTRAN FORMAT IS (1P,5E16.9)
      3. THE FIFTH PARAMETER OF THE OUTPUT4 MODULE CAN BE USED TO INCREASE THE NUMBER OF SIGNIFICANT DIGITS.
     USER ACTION:
      1. IF THE NUMBER OF SIGNIFICANT DIGITS IS ACCEPTABLE, THEN NO ACTION IS REQUIRED.
      2. IF ADDITIONAL SIGNIFICANT DIGITS ARE REQUIRED, THEN INCREASE THE VALUE OF THE FIFTH PARAMETER, AND
         RERUN THE JOB.
DATA BLOCK MSAA    WRITTEN ON FORTRAN UNIT   33 FROM DMAP MODULE OUTPUT4 IN ASCII FORMAT (1P,5E16.9)         
TRAILER =     102     750     750       6       2    1500    9858
1    CONROD                                                               SEPTEMBER   1, 2008  MSC.NASTRAN  9/23/04   PAGE  1019
                                                                                                                                    
0                                                                                                                                   
* * * *  D B D I C T   P R I N T  * * * *      SUBDMAP = PRTSUM  ,  DMAP STATEMENT NO.     30



0                                   * * * *  A N A L Y S I S  S U M M A R Y  T A B L E  * * * *
0 SEID  PEID PROJ VERS APRCH      SEMG SEMR SEKR SELG SELR MODES DYNRED SOLLIN PVALID SOLNL LOOPID DESIGN CYCLE SENSITIVITY
--------------------------------------------------------------------------------------------------------------------------
     0     0    1    1 '        '    T    T    T    T    T     T      T      T      0     F     -1            0           F
0SEID = SUPERELEMENT ID.
PEID = PRIMARY SUPERELEMENT ID OF IMAGE SUPERELEMENT.
PROJ = PROJECT ID NUMBER.
VERS = VERSION ID.
APRCH = BLANK FOR STRUCTURAL ANALYSIS.  HEAT FOR HEAT TRANSFER ANALYSIS.
SEMG = STIFFNESS AND MASS MATRIX GENERATION STEP.
SEMR = MASS MATRIX REDUCTION STEP (INCLUDES EIGENVALUE SOLUTION FOR MODES).
SEKR = STIFFNESS MATRIX REDUCTION STEP.
SELG = LOAD MATRIX GENERATION STEP.
SELR = LOAD MATRIX REDUCTION STEP.
MODES = T (TRUE) IF NORMAL MODES OR BUCKLING MODES CALCULATED.
DYNRED = T (TRUE) MEANS GENERALIZED DYNAMIC AND/OR COMPONENT MODE REDUCTION PERFORMED.
SOLLIN = T (TRUE) IF LINEAR SOLUTION EXISTS IN DATABASE.
PVALID = P-DISTRIBUTION ID OF P-VALUE FOR P-ELEMENTS
LOOPID = THE LAST LOOPID VALUE USED IN THE NONLINEAR ANALYSIS.  USEFUL FOR RESTARTS.
SOLNL = T (TRUE) IF NONLINEAR SOLUTION EXISTS IN DATABASE.
DESIGN CYCLE = THE LAST DESIGN CYCLE (ONLY VALID IN OPTIMIZATION).
SENSITIVITY = SENSITIVITY MATRIX GENERATION FLAG.
** USER WARNING MESSAGE 6450 (OUTPT4)
     THE SELECTION OF THE  ASCII FORMAT OPTION IN THE OUTPUT4 MODULE FOR DATABLOCK X2OA     MAY RESULT IN NUMERIC TRUNCATION.
     USER INFORMATION:
      1. THE FORTRAN FORMAT BEING USED IS (1P,5E16.9)
      2. THE DEFAULT FORTRAN FORMAT IS (1P,5E16.9)
      3. THE FIFTH PARAMETER OF THE OUTPUT4 MODULE CAN BE USED TO INCREASE THE NUMBER OF SIGNIFICANT DIGITS.
     USER ACTION:
      1. IF THE NUMBER OF SIGNIFICANT DIGITS IS ACCEPTABLE, THEN NO ACTION IS REQUIRED.
      2. IF ADDITIONAL SIGNIFICANT DIGITS ARE REQUIRED, THEN INCREASE THE VALUE OF THE FIFTH PARAMETER, AND
         RERUN THE JOB.
DATA BLOCK X2OA    WRITTEN ON FORTRAN UNIT   45 FROM DMAP MODULE OUTPUT4 IN ASCII FORMAT (1P,5E16.9)         
TRAILER =     101   19158     750       2       2    1500   10000

No PARAM values were set in the Control File.

1                                        * * * END OF JOB * * *

chenminghuafz

请明白人指点一二@！

chenminghuafz

蓝博士您指出的：请严格注意通道号UNIT   45？
没有理解您说的意义？

zhangpengwei

No PARAM values were set in the Control File.
你是不是将模板改动过，可能是修改错了，有些参数没有设置。

chenminghuafz

恩  是的，我模板改过，严格按照模板类型来改的，就是插入了dmap，也成功生成了out2 ，out4等文件