ansys小白 关于一个材料属性的error求助各位高手

liusiyuansjtu32

ansys小白一名，正在使用ansys做电阻点焊的模拟，在对材料的参数进行测试测试时，遇到一个错误，请各位高手帮忙分析下，谢谢！
这是设置材料属性的代码
!********************Low carbon steel******************
LCS=3

!Density
MP,DENS,LCS,7800

!Possion's ration
MP,PRXY,LCS,0.3

!Young's modulus
MPTEMP,1,20,100,300,500,700,900
MPTEMP,7,1000,1300,1500,1525,2000
MPDATA,EX,LCS,1,207e9,204e9,192e9,174e9,137e9,103e9
MPDATA,EX,LCS,7,86e9,40e9,10e9,5e9,1e9

!Specific heat
MPTEMP,1,20,93,204,315,426,527
MPTEMP,7,649,727,770,927,1500,1525
MPTEMP,13,1727
MPDATA,C,LCS,1,443,452,511,561,611,701
MPDATA,C,LCS,7,762,1003,1400,600,708,825
MPDATA,C,LCS,13,850

!Thermal conductivity
MPTEMP,1,20,100,200,300,400,500
MPTEMP,7,600,700,800,900,1000,1100
MPTEMP,13,1300,1400,1500,1525,1600,2000
MPDATA,KXX,LCS,1,74.7,59.7,55.4,49.1,38,36
MPDATA,KXX,LCS,7,35,33,26.5,27.5,28.5,29.5
MPDATA,KXX,LCS,13,32,35,37.5,38,38.2,40

!Thermal expansion coefficient
MPTEMP,1,20,200,300,400,500,600
MPTEMP,7,700,800,900,920,1000,1100
MPTEMP,13,1500,1525,1900,2100,2200,2300
MPDATA,ALPX,LCS,1,11.25e-6,13.3e-6,14.0e-6,14.6e-6,14.9e-6,15.20e-6
MPDATA,ALPX,LCS,7,15.2e-6,15.1e-6,15.1e-6,14.25e-6,14.75e-6,15.5e-6
MPDATA,ALPX,LCS,13,15.8e-6,2.5737e-5,2.685e-5,2.427e-5,2.3158e

!Bulk resistivity
MPTEMP,1,20,100,200,400,600,700
MPTEMP,7,901,1100,1300,1500,1525,2000
MPTEMP,13,2100,2200,2300,2400,2500,2600
MPDATA,RSVX,LCS,1,1.02e-7,1.63e-7,2.22e-7,4.43e-7,7.42e-7,9.13e-7
MPDATA,RSVX,LCS,7,11.23e-7,1.173e-6,1.223e-6,1.229e-6,1.39e-6,1.471e-6


经运行后，在运行

!Thermal conductivity
MPTEMP,1,20,100,200,300,400,500
MPTEMP,7,600,700,800,900,1000,1100
MPTEMP,13,1300,1400,1500,1525,1600,2000
MPDATA,KXX,LCS,1,74.7,59.7,55.4,49.1,38,36
MPDATA,KXX,LCS,7,35,33,26.5,27.5,28.5,29.5
MPDATA,KXX,LCS,13,32,35,37.5,38,38.2,40



发现如下错误：
Error：Duplicate temperature values were found. The MPTEMP command is ignored.