请教蓝博士三个小问题~

lancelot1984

1.在用EXCITE Designer 时,在load data部分时,cylinder pressure data里面的速度我能只输入一个6000吗?
2.来LOAD ITEM的Auto-Gen.crank Train Loads 里的re-caculate出现下面的错误报告,这是怎么回事?
      Error at cylinder  1: Load condition "Interpolated(Speed)" doesn't exist!
      Error at cylinder  2: Load condition "Interpolated(Speed)" doesn't exist!
      Error at cylinder  3: Load condition "Interpolated(Speed)" doesn't exist!
      Error at cylinder  4: Load condition "Interpolated(Speed)" doesn't exist!
      Action: Check Gas Force node of the active case!
3.load items这个项目是不是自动生成曲柄连杆载荷的意思啊?那下面的load cases呢?

DrLan

1.在用EXCITE Designer 时,在load data部分时,cylinder pressure data里面的速度我能只输入一个6000吗?
蓝：Interpolated(Speed)鼠标右键加转速，再分别填入转速，调入相应燃气压力曲线，注意单位！！

2.来LOAD ITEM的Auto-Gen.crank Train Loads 里的re-caculate出现下面的错误报告,这是怎么回事?
      Error at cylinder  1: Load condition "Interpolated(Speed)" doesn't exist!
      Error at cylinder  2: Load condition "Interpolated(Speed)" doesn't exist!
      Error at cylinder  3: Load condition "Interpolated(Speed)" doesn't exist!
      Error at cylinder  4: Load condition "Interpolated(Speed)" doesn't exist!
      Action: Check Gas Force node of the active case!
蓝：把上述燃气压力曲线加上就不会出这样的错了。

3.load items这个项目是不是自动生成曲柄连杆载荷的意思啊?那下面的load cases呢?
蓝：Designer使用时，你就不要管这下面的设定了，全是自动产生的AUTO-GEN。

lancelot1984

我在RUN的时候又出现以下的问题了,这是怎么回事?
Starting Pre-Processing...
    TASK: Designer Torsion ...
    ===== Updating Load Data...
         Re-calculating Gas Forces...
         ...done re-calculating Gas Forces.
    ----- ...done updating Load Data.
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    Warning! Interpolated Load Item "External Torque" is out of range of defined speeds!
    (Using nearest defined speed.)
    TASK: Create Results ...
finished Pre-Processing

Starting Job Submission...
   submitting Designer Set 1.Case 1
finished Job Submission.

DrLan

首先，你先研究一下安装例子。
其次，出错信息仔细看看，想想，试试。

lancelot1984

蓝博士你好,我想再问两个名词
crankshaft_TMean
crankshaft_TVar
是什么意思,代表什么地方的载荷

DrLan

crankshaft_TMean输出扭矩均值
crankshaft_TVar输出扭矩偏差