缩减空间不够，如何修改
大家好，我缩减模型的时候，出现了磁盘空间的不足的错误，除了减小模型外，有没有其他办法？*** USER FATAL MESSAGE 1250 (BIOWRT)
STATUS = 112, FILX = 5, LOGNAME = SCR300, NSBUF3 = 32768
FILE = c:/scratch/block_smot_cond_v2005_cms.T2776_8.SCR300
BLKNBR = 47327
ERROR MESSAGE IS --
磁盘空间不足。
BIOMSG: ERROR 923 HAS OCCURRED IN ROUTINE IONAST, FILE INDEX = 5.
LOGICAL NAME IS SCR300
FILENAME IS c:/scratch/block_smot_cond_v2005_cms.T2776_8.SCR300
STATUS = 112
********* NASTRAN FILE TABLE *********
INDEXLOGNAME STREAM_ID NAME
1SCRATCH 00000001 c:/scratch/block_smot_cond_v2005_cms.T2776_8.SCRATCH
2OBJSCR 00000002 c:/scratch/block_smot_cond_v2005_cms.T2776_8.OBJSCR
3MASTER 00000003 c:/scratch/block_smot_cond_v2005_cms.T2776_8.MASTER
4DBALL 00000004 c:/scratch/block_smot_cond_v2005_cms.T2776_8.DBALL
5SCR300 00000005 c:/scratch/block_smot_cond_v2005_cms.T2776_8.SCR300
6MASTERA FFFFFFFA c:/msc.software/md_nastran/md2008/i386/SSS.MASTERA
7MSCOBJ FFFFFFF9 c:/msc.software/md_nastran/md2008/i386/SSS.MSCOBJ
8MSCSOU FFFFFFF8 c:/msc.software/md_nastran/md2008/i386/SSS.MSCSOU
*** SYSTEM FATAL MESSAGE 4276 (IONAST)
ERROR CODE 923 PID= 0
USER INFORMATION: THIS ERROR MAY BE CAUSED BY EXCEEDING THE CAPACITY OF A SYSTEM RESOURCE.
(E.G., ALLOCATED DISK IS FULL, OR MAXIMUM FILE SIZE HAS BEEN REACHED)
*** USER INFORMATION MESSAGE 4276 (IONAST)
THE DIAG 44 RELATED A NASTRAN DUMP IS SENT TO LOG FILE.
USER ACTION: THIS INFORMATION MAY BE USEFUL TO MSC FOR DEBUGGING YOUR PROBLEM.
PLEASE CONTACT MSC CLIENT SUPPORT.
我的缩减模板如下：NASTRAN BUFFSIZE=65537
NASTRAN SYSTEM(213)=1
NASTRAN SYSTEM(1)=32769
NASTRAN SYSTEM(146)=1 $ SPACE SAVING METHOD FOR LANCZOS
NASTRAN SYSTEM(151)=1 $ SPILL OF THE SRC300 PARTITION
NASTRAN SYSTEM(166)=0 $ NO ACTION AFTER SPARSE DECOMP. CONTROL
$
INIT MASTER(S) $ DELETE DB AT THE END OF THE RUN
$
$ ------------ FILE MANAGEMENT SECTION ----------------------------------------
$
$INIT DBALL LOGICAL=(DB1(30gb),DB2(30gb))
$INIT SCRATCH(MEM=1000) LOGICAL=(A(100)),SCR300=(SC300(50gb))
$
$ASSIGN DB1='Primer_Block_SMOT_01.DBALL'
$ASSIGN DB2='Primer_Block_SMOT_02.DBALL'
$
$ASSIGN A='Primer_Block_cond_SMOT_0.scr'
$ASSIGN B='Primer_Block_cond_SMOT_01.scr_50gb'
模板如何修改，可以给缩减分配更多的空间？
LZ你好。。小弟最近在做缩减。。请问您有没有缩减的例子？我急需啊。。能不能麻烦楼主给小弟发几个例子？邮箱629828472@qq.com snowcube 发表于 2013-4-18 09:23 static/image/common/back.gif
LZ你好。。小弟最近在做缩减。。请问您有没有缩减的例子？我急需啊。。能不能麻烦楼主给小弟发几个例子？邮 ...
我之前也是参照excite自带的例子做的，手上目前做的是项目，就不方面给你了。。。 建议你留一块足够大的硬盘200G，然后就不要再设定指定硬盘空间，即刪除命会中FILE MANAGEMENT 部分 DrLan 发表于 2013-4-28 22:04 static/image/common/back.gif
建议你留一块足够大的硬盘200G，然后就不要再设定指定硬盘空间，即刪除命会中FILE MANAGEMENT 部分 ...
谢谢，蓝博士！
页:
[1]