找回密码
 注册
Simdroid-非首页
楼主: timebirds

【置顶讨论】ansys出错及警告信息汇总,鼓励解答问题,加分!!!!

[复制链接]
发表于 2007-8-10 10:26:11 | 显示全部楼层 来自 北京
楼上的朋友,我运行你的帖子,没有发现错误啊,只是在施加扭矩的时候出现一个警告:
Both solid model  and finite element model boundary conditons-----等等(我就不全写上了)
这个警告是正常的阿,只是告诉你要将所有的力转化到节点或者单元上,没有什么问题啊。我不明白你说的做刚性连接施加扭矩出错指的是什么?
回复 不支持

使用道具 举报

发表于 2007-8-12 20:11:34 | 显示全部楼层 来自 浙江宁波
Simdroid开发平台
楼主总结的太好了,谢谢
回复 不支持

使用道具 举报

发表于 2007-8-13 23:32:12 | 显示全部楼层 来自 湖南长沙
好贴就要顶啊顶,
回复 不支持

使用道具 举报

发表于 2007-8-14 07:47:24 | 显示全部楼层 来自 北京大兴
原帖由 sh_lin30 于 2007-5-8 19:25 发表
我在做接触分析时,遇到如下warning
some contact elements overlap with the other contact element which can cause over constraint

其原因是不是也是因为网格质量不好所致?

因为模型较大,所以,没 ...



这是由于在同一实体上,即有绑定接触(MPC)的定义,又有刚性区或远场载荷(MPC)的定义,操作中注意在定义刚性区或远场载荷时避免选择不必要的DOF自由度,以消除过约束


-------------------
你又是自问自答啊。不过解答得不错。,by wishangtian

[ 本帖最后由 wishangtian 于 2007-8-14 08:47 编辑 ]

评分

1

查看全部评分

回复 不支持

使用道具 举报

发表于 2007-8-27 11:02:09 | 显示全部楼层 来自 安徽合肥
划分网格时出现警告:
Shape testing revealed that 450 of the 1500 new or modified elements   
violate shape warning limits.
是什么原因造成的呢?
回复 不支持

使用道具 举报

发表于 2007-8-27 22:43:20 | 显示全部楼层 来自 北京丰台
原帖由 yeyingwy 于 2007-8-27 11:02 发表
划分网格时出现警告:
Shape testing revealed that 450 of the 1500 new or modified elements   
violate shape warning limits.
是什么原因造成的呢?


单元网格质量不够好
尽量,用规则化网格,或者再较为细密一点
回复 不支持

使用道具 举报

发表于 2007-8-31 16:14:32 | 显示全部楼层 来自 浙江杭州

对两空间曲面进行倒角时出现以下错误!

在用Area Fillet对两空间曲面进行倒角时出现以下错误:Area 6 offset could not fully converge to offset distance 10. Maximum error between the two surfaces is 1% of offset distance.请问这是什么错误?怎么解决?其中一个是圆柱接管表面,一个是碟形封头表面。
回复 不支持

使用道具 举报

发表于 2007-9-4 14:55:29 | 显示全部楼层 来自 河北保定
There are 21 small equation solver pivot terms.;
SOLID45 wedges are recommended only in regions of relatively low        
stress gradients.
第一个问题我自己觉得是在建立contact时出现的错误,但自己还没有改正过来;第二个也不知道是什么原因。
还有一个:initial penetration 4.44089×10E-6 was detacted between contact element 53928 and target element 53616;也是建立接触是出现的,也还没有接近。唉,郁闷中!!
回复 不支持

使用道具 举报

发表于 2007-9-6 09:36:15 | 显示全部楼层 来自 江苏南京
原帖由 jiayi1086 于 2007-8-31 16:14 发表
在用Area Fillet对两空间曲面进行倒角时出现以下错误:Area 6 offset could not fully converge to offset distance 10. Maximum error between the two surfaces is 1% of offset distance.请问这是什么错误? ...

ansys的布尔操作能力比较弱。
如果一定要在ansys里面做的话,那么你试试看先对线进行倒角,然后由倒角后的线形成 倒角的面。
建议最好用UG、PRO/E这类软件生成实体模型然后导入到ansys。
回复 不支持

使用道具 举报

发表于 2007-9-6 09:40:34 | 显示全部楼层 来自 江苏南京
原帖由 wangguangqing 于 2007-9-4 14:55 发表
There are 21 small equation solver pivot terms.;
SOLID45 wedges are recommended only in regions of relatively low        
stress gradients.
第一个问题我自己觉得是在建立contact时出现的错误,但 ...


第一个问题:There are 21 small equation solver pivot terms.;
不是建立接触对的错误,一般是单元形状质量太差(例如有i接近零度的锐角或者接近180度的钝角)造成small equation solver pivot terms

第二个问题:SOLID45 wedges are recommended only in regions of relatively low        
stress gradients.
这只是一个警告,它告诉你:推荐SOLID45单元只用在应力梯度较低的区域。
它只是告诉你注意这个问题,如果应力梯度较高,则可能计算结果不可信。
回复 不支持

使用道具 举报

发表于 2007-9-8 09:34:50 | 显示全部楼层 来自 山西太原
ansys生成mnf文件导放adams时,出现Error estimation is not available for PowerGraphics.The ERNORM command is ignored.
这是怎么回事呀?
回复 不支持

使用道具 举报

发表于 2007-9-11 22:27:02 | 显示全部楼层 来自 山西太原
怎么没有人帮我解答呢??
ansys向adams导的过程中,出现如下问题
There is not enough memory for the Sparse Matrix Solver to proceed.Please shut down other applications that may be running or increase the virtual memory on your system and return ANSYS.Memory currently allocated for the Sparse Matrix Solver=50MB.Memory currently required for the Sparse Matrix Solver to continue=25MB
可是我的内存不小呀,512MB应该够了吧,我设的虚拟内存4072MB,也应该够了吧。
那位大哥大姐帮忙看一下呀
回复 不支持

使用道具 举报

发表于 2007-9-12 09:19:27 | 显示全部楼层 来自 江苏南京

回复 #112 shuizhongzhou 的帖子

不清楚你ansys导入adams过程中怎么还需要使用Sparse Matrix Solver(稀疏矩阵求解器)。
估计是scrach memery太低了,
从ansys product launcher 进入 设置内存,
total workspace和 dataspace的差就是scrach memery
如我给的图中所示,total workspace 1150MB
dataspace200MB,
scrach memery 就是1150-200=950MB

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?注册

×
回复 不支持

使用道具 举报

发表于 2007-9-13 00:06:28 | 显示全部楼层 来自 湖南长沙

ansys内存不足

我用ansys做三维静电场模拟,用solid122,图形为内外两个同轴金属导体,然后导体中间为锥形线圈,线圈和导体不接触,每个线圈上加不同电,划分网格的时候太粗要报错,太细也报错,好不容易画好了,然后一模拟又老说内存差224M,现有内存40M。我电脑是1G的内存啊。郁闷,搞了三天了!请高手指点!
回复 不支持

使用道具 举报

发表于 2007-9-24 19:09:32 | 显示全部楼层 来自 山西太原
我是做多体动力学分析的
做柔性体时用ansys生成mnf文件时,出现Error estimation is not available for PowerGraphics.The ERNORM command is ignored.
这是怎么回事呀?
后来我试着把PowerGraphics给关了,这样ansys到是不再出现在警告了,可是生成mnf文件时却丢了几个矩陈.
我划的网格没有问题呀,都检查过了,没有错的和警告.,为什么会出现这种情况,请大家帮帮忙,急!!
回复 不支持

使用道具 举报

发表于 2007-9-26 12:31:29 | 显示全部楼层 来自 山西太原
昨天我换了种方法,改用beam单元连接,可是生成mnf时,先是提示Lagrange multiplier based element can not be used in substructuer generation pass,
然后我点了确定后,又提示Superelement file subelem. sub is not available
这是怎么回事,那位高手知道呀?
这里怎么这么冷清,版主不知道在不在,怎么总是没有人回答,不知道是没遇到过,还是别的....
回复 不支持

使用道具 举报

发表于 2007-9-28 21:20:28 | 显示全部楼层 来自 山西太原
还是没人理,唉,高手都去那了
回复 不支持

使用道具 举报

发表于 2007-10-2 19:38:20 | 显示全部楼层 来自 北京交通大学

回复 #106 sh_lin30 的帖子

Previous testing revealed that 1660 of the 2234 selected elements      
violate shape warning limits.  To review warning messages, please see   
the output or error file, or issue the CHECK command.
这个警告也是网格划分的原因吗?还是说单元奇异阿?可以不用理会吗?谢谢
回复 不支持

使用道具 举报

发表于 2007-10-2 19:45:52 | 显示全部楼层 来自 北京交通大学

后处理中的一个问题

在进行时间历程后处理的时候出现的下面问题:
Result File Mismatch
the result file "file.rst"may have been solved using different modal data than currently stored. results may be erroneous.do you want the database cleared ?
可怕的是不管加什么样的地震波,得出来得应力值都是一样的,但是位移不一样,谁遇到过这类问题啊?谢谢了!!
回复 不支持

使用道具 举报

发表于 2007-10-5 00:31:31 | 显示全部楼层 来自 重庆沙坪坝区

急问

我在hypermesh中建立了实体单元、壳单元,mpc184单元,倒入到ansys出现警告:
1.specified range 0 to 0 is not permitted. the esel command is ignored.这个警告是在导入网格后出现的。
2.the selected element set contains mixed element stiffness types. this would invalidate error estimation.这个是在计算完了时出现的。
这两个警告是什么意思?我在计算时关闭了误差估计。

[ 本帖最后由 mncaojing 于 2007-10-5 00:33 编辑 ]
回复 不支持

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|小黑屋|联系我们|仿真互动网 ( 京ICP备15048925号-7 )

GMT+8, 2024-3-29 14:27 , Processed in 0.046714 second(s), 9 queries , Gzip On, MemCache On.

Powered by Discuz! X3.5 Licensed

© 2001-2024 Discuz! Team.

快速回复 返回顶部 返回列表